Apc Silcon DP300E Series Bedienungsanleitung Seite 21
- Seite / 38
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
21User Guide Silcon DP300E Series 480V 400-500kVA
7OA0004 US rev. 02
Programming Parameters
4.5 Parallel programming/operation
Programming parameters for advanced parallel operation
To use the advanced parallel functions the following parameters must be pro-
grammed:
1. “Station number”
2. “Highest station address”
3. “Advanced power management”
4. “APM test mode active”
5. “Battery connection”
Description of settings.
1. “Station number”
• Valid station numbers: 1-9 stating the UPS parallel address in the system.
2. “Highest station number”
• Valid station numbers: 2-9 stating the number of UPS’s in the system.
3. “Advanced power management”
• “Disabled”: Advanced power management is inactive.
• “PARALLEL+1”: Advanced power management is activated when the system
operates as PARALLEL+1, meaning that one system can be isolated without
overloading the remaining systems (N systems/UPS).
• “REDUNDANT+1”: Advanced power management is activated when the
system operates as REDUNDANT+1, meaning that one system can be
isolated without overloading the remaining systems (N systems/UPS) with
one spare system.
4. “APM test mode active”
• “No”: Stand-by time will be 24 hours - on-line time will be 48 hours * N
systems.
• “Yes”: Stand-by time will be 1 min. - on-line time will be 2 min. * N systems.
5. “Battery connection”
• “Separate”: Separate battery for this UPS.
• “Common”: Common battery in a parallel system. When this setting is
chosen, the highest battery temperature that can be found in the parallelled
systems is used (for charge voltage compensating).
Programming guide.
Example with 3 systems in parallel with separate batteries.
• Programme the station addresses 1-3: 1 for UPS 1, 2 for UPS 2 and 3 for UPS 3
• All UPS systems have to be programmed to “Highest station address” = 3.
• If APM should not be tested, “APM test mode active” must be “NO”.
• If a system is isolated due to service the station numbers must be reprogrammed
for the remaining active systems starting with number 1 and ending with max.
number of active systems. No numbers must be left out in this sequence. Fur-
thermore “Highest station address” must be changed to number of active UPS’s
in parallel.
NOTE:
Common battery pack is a
technical possibility.
However, APC recommend
separate battery pack due to a
higher safety degree in con-
nection with redundant/parallel
operation.
The UPS system is prepared
for both solutions.
- Silcon DP300E Series 1
- 480V 400–500kVA 1
- User Guide 1
- IMPORTANT SAFETY INSTRUCTIONS 2
- SAVE THESE INSTRUCTIONS 2
- Table of Contents: 3
- Introduction 4
- Bypass Panel 5
- CAUTION! 5
- 7OA0004 US rev. 02 10
- Operation 15
- Programming Parameters 16
- Programming parameters 18
- Measurements 24
- 6.0 Alarms - What To Do 25
- 6.4 The events logger 26
- 6.6 Possible alarms 27
- Remote Display 30
- Preventive Maintenance 32
- Economy Operation 36
- System Specifications 37
- How to Contact APC 38
Verwandte Produkte und Handbücher für Werkzeug Apc Silcon DP300E Series
Werkzeug Apc RS 500 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Werkzeug Apc 1000VA Bedienungsanleitung
(1 Seiten)
(1 Seiten)
Rockwell Automation 2080-LC30-48AWB_48QWB_48QVB_48QBB Micro830 48 Poin manuali
Manuali dei proprietari e guide per l'utente per Apparecchiature Rockwell Automation 2080-LC30-48AWB_48QWB_48QVB_48QBB Micro830 48 Poin.
We fornisce 1 manuali pdf Rockwell Automation 2080-LC30-48AWB_48QWB_48QVB_48QBB Micro830 48 Poin per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Kommentare zu diesen Handbüchern