APC AR1100 Betreibershandbuch Seite 81
- Seite / 144
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
67
OPERATING PROCEDURES: NT (Tonometry) Measurement: NT Mode
2
<Error messages during NT measurement>
• If the measurement was not performed correctly for some reasons, an abbreviated error
message is displayed above the measurement range indication.
In this case, eliminate the cause of the error, following the suggestions in the table below and
perform the measurement again.
Error message Description
ALM
(Alignment error)
Alignment is not proper.
Perform the alignment and the measurement again.
APL
(Applanation error)
As the eye was not opened enough, corneal applanation was
insufficient.
Instruct the patient to open his or her eyes wider.
If the patient cannot do so, ask an assistant to open the eyelids wider by
using a swab, etc.
OVR
(Over the measurement range)
The intraocular pressure exceeds the preset measurement range.
Switch the measurement range to “APC 60” or “60” and perform the
measurement again.
BLK
(Blinking of the eye)
The measurement is impossible because of blinking and slight
movement of the eye.
Instruct the patient not to blink or move the eye until the measurement is
completed.
After the eye stopped blinking and moving, perform the measurement again.
PCE
(APC error)
The patient’s eye cannot be measured with the air pressure which is
controlled by the APC function because of substantial fluctuation in
intraocular pressure.
Switch the measurement range from “APC 40” to “40” or from “APC 60” to
“60”.
TOO CLOSE
The space between the patient’s eye and the air nozzle is 9 mm or less.
Pull the joystick backward to increase the space between them.
NO SEARCH
The alignment spot cannot be detected.
CHECK THE EYE
This error appears when five consecutive APL errors with measurement
values occur.
Check the condition of the patient’s eye.
When APL errors continuously occur with no measurement values, this error
is not displayed.
OPEN THE EYE WIDER
Alignment is proper, but the eyelid detection lights cannot be detected.
Instruct the patient to open his/her eyes wider.
This error occurs only when the eyelid detection mode is turned on.
ÁÐÃᴱ°
ÁÖ¯µ
ÁÖ¯µ
ᵏ
ǽ
ǽᴮᴲǽǽǽᴮᴱ
ǽᴮᴲǽǽǽᴮᴱ
ǽᴮᴰǽǽǽᴮᴱ
ǽᴮᴱ®ᴭǽᴮᴱ®ᴭ
ᴮᴲ
Á
Ð
Ì
Error message and measured data
- OPERATOR 1
- S MANUAL 1
- August 2007 2
- 15601-P902B 2
- Printed in JAPAN 2
- Use precautions 4
- During Use 6
- Wavelength (nm) 8
- After Use 9
- Maintenance 10
- Disposal 10
- { Patient environment 11
- Table of Contents 12
- BEFORE USE 15
- 1.2 Indications for Use 16
- 1.3 Principles 17
- 1.4 Device Description 18
- { Rear view 20
- { Bottom view 22
- 1.5.1 R/K measurement screen 23
- ǁᵃᵆᵋᵆᵐᵅǂ 25
- Parameter button 27
- 1.5.2 NT measurement screen 28
- ÁÖ 29
- [Underside view] 31
- 1.7 Checking Contents 32
- 1.8 Before First Use 33
- 9 Set the printer paper 34
- { Setting by parameter 35
- BEFORE USE: Before First Use 36
- OPERATING PROCEDURES 37
- Turn the power switch on ( ) 38
- 3 Perform checks before use 39
- 5 Prepare the patient 40
- 7 Print the measured results 42
- 㧹㧱㧭㧿㨁㧾㧵㧺㧳ޓ㨃㧵㧺㧰㧻㨃 44
- ޓޓޓޓ㧯㧴㧱㧯㧷㧵㧺㧳 44
- 㨃㧵㧺㧰㧻㨃ޓ㧯㧴㧱㧯㧷ޓ㧻㧷㧍 44
- 2.3.1 Normal shutoff 47
- 2.4 Selecting the Mode 49
- 2.4.2 Sleep mode 52
- Measurements 53
- 4 Measurement starts 57
- 5 Measurement completes 59
- 9 Print the measured results 60
- { CATARACT measurement mode 61
- 2 Measurement completes 64
- KM Measurement Mode 65
- ᴹᵀᵌᵏᵋᵂᴾᵉǽᵐᵆᵗᵂᴻ 67
- ᵐᵑᴾᵏᵑǽᵐᵔǽᴷǽᵀᴾᵍᵑᵒᵏᵂ 67
- PS (Pupil Size) Measurement 69
- ᴹᵍᵒᵍᵆᵉǽᵐᵆᵗᵂᴻ 70
- Manual PD Measurement 71
- to exit from PD mea 72
- Contact lens 73
- ÁÖ 77
- ÁÖ 77
- 8 Start the measurement 80
- 2.6.1 Eyelid detection mode 84
- 2.7 Printing 85
- <Sample printout 2> 86
- 2.7.2 Eyeprint 88
- 2 Press the print button 89
- 2.8 Parameter Settings 90
- { Resetting the parameters 92
- 2.8.1 Parameter tables 93
- [KM (KM measurement)] 94
- [NT (NT measurement)] 94
- [PRINT1 (Print setting 1)] 96
- [PRINT2 (Print setting 2)] 97
- [PRINT3 (Print setting 3)] 99
- 㧞㧠ޓ㧝㧣㧦㧜㧜 103
- 2.8.3 Entering comments 105
- 3.1.1 Outline 107
- 3.1.2 Connecting procedure 108
- 3.1.3 Operating procedure 108
- 3.2.1 Outline 109
- 3.2.2 Connecting procedure 109
- 3.2.3 Operating procedure 110
- 3.3.1 Outline 111
- 3.3.2 Method of connection 111
- 2 Perform measurements 112
- 3 Press the print button 112
- 2 Insert the Eye Care card 113
- MAINTENANCE 115
- 4.3 Replacing Printer Paper 120
- 3 Insert new printer paper 121
- 4.4 Fixing Chinrest Paper 122
- 4.6 Cleaning 125
- 4.6.2 Cleaning the air nozzle 127
- 4.7 List of Replacement Parts 128
- 5.1 Classifications 129
- 5.2 Safety Features 130
- 5.3 Specifications 131
- { Other functions 133
- { Dimensions and weight 133
- { Others 133
- 5.4 Standard Configuration 134
- EMC (IEC 60601-1-2: 2001) 135
- GLOSSARY 139
- GLOSSARY: 140
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern