APC INROOM ACPSC3000 Betriebsanleitung Seite 91
- Seite / 106
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
91InRoom Controller - Operating Instructions
Cause Alarm message Effect
LP switch/LP threshold passed under LOW PRESSURE 1 Compressor 1 off, compressor 2 on,
if present
HP switch/HP threshold exceeded
Internal compressor power switch
COMP 1 FAILURE/HP
Compressor 1 off, compressor 2 on,
if present
LP switch/LP threshold passed under LOW PRESSURE 2 Compressor 2 off, compressor 1 on
HP switch/HP threshold exceeded
Internal compressor power switch
COMP 2 FAILURE/HP Compressor 2 off, compressor 1 on
Temperature switch/heating MCB E-HEAT # FAILURE
Heating # off
Humidifier MCB HUMIDIFIER # FAIL Humidifier # off
Airflow differential switch AIRFLOW FAILURE #
all components off
Filter differential switch FILTER ALARM no direct effect*
External alarm signal
EXTERNAL ALARM # no direct effect*
Conductivity >5µS HUMIDIFIER # 5µS no direct effect*
Conductivity >20µS HUMIDIFIER # 20µS Ultrasonic humidifier off
Glycol pump MCB GLYCOL PUMP # FAILURE Compressors & pump off
G-Pump MCB G-PUMP FAILURE Compressors & pump off
GE-Pump MCB GE-PUMP FAILURE Compressors & pump off
Drycooler # MCB DRYCOOLER # FAIL Compressor, pump & drycooler # off
Water detector WATER ALARM Humidifier, dehumidification off
Return air temp. > limit value RETURN AIR TEMP TOO HIGH no immediate effect
Return air humidity > limit value RETURN AIR HUM TOO HIGH no immediate effect
Supply air temp. > limit value SUPPLY AIR TEMP TOO HIGH no immediate effect
Supply air humidity > limit value SUPPLY AIR HUM TOO HIGH no immediate effect
Water temp. > limit value WATER TEMP TOO HIGH no immediate effect
Return air temp. < limit value RETURN AIR TEMP TOO LOW no immediate effect
Return air humidity < limit value RETURN AIR HUM TOO LOW no immediate effect
Supply air temp. < limit value SUPPLY AIR TEMP TOO LOW no immediate effect
Supply air humidity < limit value SUPPLY AIR HUM TOO LOW no immediate effect
Water temp. < limit value WATER TEMP TOO LOW no immediate effect
Fire/smoke detector
FIRE ALARM all components off
Tolerance exceeded
SENSOR # EXCESS faulty sensor # excluded
Measured voltage/current out of defined
range
SENSOR # DEFECT faulty sensor # excluded
7.2 Alarm messages
# stands for a number.
* The corresponding alarm can be cofigured to release a common alarm which can control further equipment by a digital
output.
** The alarm text can be configured.
- Operating Instructions 1
- Contents 3
- 1. Presentation of the system 5
- 2. Hardware components 6
- 2.2.1 Board design 9
- 2.2.2 Assignment - EDIO1 10
- 2.2.3 Assignment - EDIO2 11
- 2.3.1 Board design 12
- 2.3.2 Assignment - EAIO 13
- 2.4.2 Assignment - EBUS 14
- 2.4.1 Board design 14
- 2.5 InRoom Controller Board 15
- 3. Operator interface 16
- 4. Bus communication 19
- 4.2 Special cases 20
- 5. Controller start 21
- Stop states 23
- Symbols for operating states 23
- Symbols for alarm messages 23
- Passwords 24
- 6. Operation 25
- 6.1.2 Info overview 26
- Display 28
- Data logger 28
- 6.2 Control level 32
- 6.2.2 Control commands 33
- A B C 34
- D E F 35
- Display Cooling 37
- Display Cooling 38
- Display Valves 39
- Display Valves 40
- Times are entered in seconds 41
- F3 F5 F6 44
- Display Humidification 45
- Humidification 46
- Dehumidification (Part 2) 47
- Display Air 49
- Is the minimum speed kept ? 50
- Display Air 52
- Function 52
- AT-Preferences 53
- Password 53
- K L M 54
- N O P 55
- Q R S 56
- T U V 57
- Display Heating 62
- Display Equipment 65
- Display Equipment 66
- Gen. settings 68
- Display Gen. settings 69
- Display Gen. settings 70
- Gen. setting 71
- Display Day & Night 72
- Due to 75
- Commands 76
- Display Data 78
- Maintenance 79
- Manual Operation 80
- 6.4 Default configurations 81
- General alarms 82
- Limit alarms 82
- Week program 82
- Components 83
- Drycooler 84
- Humidifiers 85
- Dehumidifier 86
- Sensors (continued) 88
- External alarms 88
- Actual value output 88
- 6.4.1 Preconfigurations 89
- 7. Alarm treatment 90
- 7.2 Alarm messages 91
- 7.3 Component-related alarms 92
- 7.4 Alarm Reset 92
- 8. Configuration notes 94
- 8.1 Loading new Software 95
- InRoom - Service 96
- 9. Network Management Card 97
- BOOTP and DHCP configuration 98
- Control console 101
- 9.2 Access a Configured Unit 102
- Telnet/SSH 103
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern