APC INROOM ACPSC3000 Betriebsanleitung Seite 97
- Seite / 106
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
97InRoom Controller - Operating Instructions
9. Network Management Card
9.1 Quick Configuration
The InRoom Precision Air Conditioner is shipped with a Network Management Card that enables you to manage
the air conditioner over your network. You must set up the Network Management Card to control the InRoom Pre-
cision Air Conditioner through a network.
The Network Management Card comes pre-assembled to an interface board using two sets of pin connections.
The interface board then connects to the controller board of the InRoom Precision Air Conditioner using a DB-15
connection, and a network connection is made by inserting an RJ-45 cable in to the ethernet port on the interface
board. The Network Management Card can be configured via a serial cable connected to the service port of the
controller board by using the nmcservice command.
Overview
You must configure the following TCP/IP settings before the InRoom Precision Air Conditioner can operate on a
network:
• IP address of the Network Management Card
• Subnet mask
• Default gateway
Note: Never use the loopback address (127.0.0.1) as the default gateway address for the
Network Management Card. Doing so will disable the card and will require you to reset TCP/IP
settings to their defaults using a local serial login.
If a default gateway is unavailable, use the IP address of a computer that is located on the same
subnet as the Network Management Card and that is usually running. The Network Management
Card uses the default gateway to test the network when traffic is very light.
See “Watchdog Features” online at www.apc.com for more information about the watchdog
role of the default gateway.
TCP/IP configuration methods
Use one of the following methods to define the TCP/IP settings needed by the Network Management Card:
• APC Device IP Configuration Wizard (See “APC Device IP Configuration Wizard” on page 98.)
• BOOTP or DHCP server (See “BOOTP and DHCP configuration” on page 98.)
• Networked computer (See “Remote access to the control console” on page 100.)
- Operating Instructions 1
- Contents 3
- 1. Presentation of the system 5
- 2. Hardware components 6
- 2.2.1 Board design 9
- 2.2.2 Assignment - EDIO1 10
- 2.2.3 Assignment - EDIO2 11
- 2.3.1 Board design 12
- 2.3.2 Assignment - EAIO 13
- 2.4.2 Assignment - EBUS 14
- 2.4.1 Board design 14
- 2.5 InRoom Controller Board 15
- 3. Operator interface 16
- 4. Bus communication 19
- 4.2 Special cases 20
- 5. Controller start 21
- Stop states 23
- Symbols for operating states 23
- Symbols for alarm messages 23
- Passwords 24
- 6. Operation 25
- 6.1.2 Info overview 26
- Display 28
- Data logger 28
- 6.2 Control level 32
- 6.2.2 Control commands 33
- A B C 34
- D E F 35
- Display Cooling 37
- Display Cooling 38
- Display Valves 39
- Display Valves 40
- Times are entered in seconds 41
- F3 F5 F6 44
- Display Humidification 45
- Humidification 46
- Dehumidification (Part 2) 47
- Display Air 49
- Is the minimum speed kept ? 50
- Display Air 52
- Function 52
- AT-Preferences 53
- Password 53
- K L M 54
- N O P 55
- Q R S 56
- T U V 57
- Display Heating 62
- Display Equipment 65
- Display Equipment 66
- Gen. settings 68
- Display Gen. settings 69
- Display Gen. settings 70
- Gen. setting 71
- Display Day & Night 72
- Due to 75
- Commands 76
- Display Data 78
- Maintenance 79
- Manual Operation 80
- 6.4 Default configurations 81
- General alarms 82
- Limit alarms 82
- Week program 82
- Components 83
- Drycooler 84
- Humidifiers 85
- Dehumidifier 86
- Sensors (continued) 88
- External alarms 88
- Actual value output 88
- 6.4.1 Preconfigurations 89
- 7. Alarm treatment 90
- 7.2 Alarm messages 91
- 7.3 Component-related alarms 92
- 7.4 Alarm Reset 92
- 8. Configuration notes 94
- 8.1 Loading new Software 95
- InRoom - Service 96
- 9. Network Management Card 97
- BOOTP and DHCP configuration 98
- Control console 101
- 9.2 Access a Configured Unit 102
- Telnet/SSH 103
Rockwell Automation 2080-LC30-48AWB_48QWB_48QVB_48QBB Micro830 48 Poin manuali
Manuali dei proprietari e guide per l'utente per Apparecchiature Rockwell Automation 2080-LC30-48AWB_48QWB_48QVB_48QBB Micro830 48 Poin.
We fornisce 1 manuali pdf Rockwell Automation 2080-LC30-48AWB_48QWB_48QVB_48QBB Micro830 48 Poin per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Kommentare zu diesen Handbüchern