APC IP DSLAM Betriebsanweisung Seite 254
- Seite / 603
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
246
= 4 bytes).
AturChanGsINPup
The actual number of Impulse Noise
Protection(INP) symbols for the upstream
interleaved channel. One symbol equals 250 µs,
so an INP of 1 correlates to a correction time of
250 µs.
AturChanGsL0up
The number of bits from the upstream latency path
function #0 included per DMT symbol.(length = 4
bytes). It is not available for ADSL.
AturChanGsM0up
The number of Mux Data Frames per FEC Data
Frame in upstream latency path function
#0.(length = 4 bytes). It is not available for ADSL.
AturChanGsT0up
The ratio of the number of Mux Data Frames to
the number of sync octets in the upstream latency
path function #0.(length = 4 bytes). It is not
available for ADSL.
AturChanGsB0up
The nominal number of octets from frame bearer
#0 per Mux Data Frame at Reference Point A in
upstream latency path function #0.(length = 4
bytes). It is not available for ADSL.
References
• ADSL commands
8.9.13 ADSL ATUR Chanperf Commands
8.9.13.1 Get adsl atur chanperf
Description: This command is used to get.
Command Syntax: get adsl atur chanperf [ifname <interface-name>]
Parameters
Name Description
ifname <interface-
name>
The ADSL interface name.
Type : Get – Optional
Valid values: dsli-0 – dsli-23
Example
$ get adsl atur chanperf ifname dsli-0
Output
Ifname : dsli-0
Perf Valid Intervals : 10
Perf Invalid Intervals : 10
Perf valid 1Day Intvl : 20
Perf Invalid 1Day Intvl : 20
PerfData Curr15Min Curr1Day Prev1Day
Time Elapsed
/Monitored(sec) - 10 10 10
Rx Blocks 10 10 10 10
Tx Blocks 10 10 10 10
Corrected Blocks 10 10 10 10
Uncorrected Blocks 10 10 10 10
NCD Count 10 10 10 10
HEC Count 10 10 10 10
NCD Failure Count 20 20 20 20
LCD Failure Count 20 20 20 20
Output Fields
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Verwandte Produkte und Handbücher für Vernetzung APC IP DSLAM
Vernetzung APC AP9312TH Betriebsanweisung
(32 Seiten)
(32 Seiten)
Vernetzung APC AP9608 Installationshandbuch
(32 Seiten)
(32 Seiten)
Vernetzung APC 66123 Installationshandbuch
(16 Seiten)
(16 Seiten)
Vernetzung APC AP9630 Betriebsanweisung
(85 Seiten)
(85 Seiten)
Vernetzung APC IP DSLAM Betriebsanweisung
(67 Seiten)
(67 Seiten)
Vernetzung APC AP9630 Bedienungsanleitung
(117 Seiten)
(117 Seiten)
Vernetzung APC AP9630 Bedienungsanleitung
(32 Seiten)
(32 Seiten)
Vernetzung APC AP9224110 Spezifikationen
(16 Seiten)
(16 Seiten)
Vernetzung APC AP9608 Spezifikationen
(9 Seiten)
(9 Seiten)
Vernetzung APC AP9608 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Rockwell Automation 2080-LC30-48AWB_48QWB_48QVB_48QBB Micro830 48 Poin manuali
Manuali dei proprietari e guide per l'utente per Apparecchiature Rockwell Automation 2080-LC30-48AWB_48QWB_48QVB_48QBB Micro830 48 Poin.
We fornisce 1 manuali pdf Rockwell Automation 2080-LC30-48AWB_48QWB_48QVB_48QBB Micro830 48 Poin per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Kommentare zu diesen Handbüchern