APC IP DSLAM Betriebsanweisung Seite 381
- Seite / 603
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
373
Type: Create － Optional
Modify － Optional
Default value: disable
ruleprio low | high
Tells the priority of the rule. Based on this
priority value, the rule is created in fast or slow
memory. This field can be modified only if
'status' has the value 'disable'. This field is
ignored if the 'ruleAction' has value 'clfrdef'
Type: Create － Optional
Modify － Optional
Default value: high
ruledir in | out
Specifies whether the rule will be applied on
incoming interfaces (ingress)or outgoing
interfaces(egress).
Type: Create － Optional
Default value: in
applywhenreq enable
|disable
This specifies whether this rule is to be applied
only when required. Rule description field is
mandatory if this field is set to value 'enable'.
This field can be modified only if 'status' has the
value 'disable'. This field is ignored if the
'ruleAction' has value 'clfrdef'.
Type: Create － Optional
Modify － Optional
Default value: disable
pkttype Mcast | Bcast
|Ucast
This field specifies the types of packets on which
this rule is to be applied. 'Mcast' means this rule
is valid for multicast packets, 'Bcast' means this
rule is valid for broadcast packets and 'Ucast'
means this rule is valid for unicast packets. This
field is valid only if 'ruleDir' is 'out'. This field can
be modified only if 'status' has the value
'disable'. Type: Create － Optional
Modify － Optional
Default value: Ucast
snooplevel interface
|bridge
Snoop level specifies whether packet will be
snooped directly from Interface or from Bridge
after applying Bridging functionality .If none of
the Rule actions is 'sendtoControl' or
'copytocontrol', then this field has no
significance. This field can be modified only if
'status' has the value 'disable'. Type: Create －
Optional
Modify － Optional
Default value: interface
exprid <exprid-val>
Identifies the expression id from the Generic
Filter Expression Table to be used. This field is
used only if 'ruleAction' is 'exprdef'. In absence
of this field, the default relationship between all
subrules is all ANDed.
Type: Create － Optional
Modify － Optional
Valid values: 1 - 65535
Default value: 0
Example
$ create filter rule entry ruleid 1 action setprio description lacp priority 7
status enable statsstatus disable ruleprio high ruledir in applywhenreq
disable pkttype Ucast snooplevel interface exprid exprid 1 actionval
0x00000000 actionmask 0xffffffff
Output
Verbose Mode On
Entry Created
Rule Id : 1 Rule Action : setprio
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Verwandte Produkte und Handbücher für Vernetzung APC IP DSLAM
Vernetzung APC AP9312TH Betriebsanweisung
(32 Seiten)
(32 Seiten)
Vernetzung APC AP9608 Installationshandbuch
(32 Seiten)
(32 Seiten)
Vernetzung APC 66123 Installationshandbuch
(16 Seiten)
(16 Seiten)
Vernetzung APC AP9630 Betriebsanweisung
(85 Seiten)
(85 Seiten)
Vernetzung APC IP DSLAM Betriebsanweisung
(67 Seiten)
(67 Seiten)
Vernetzung APC AP9630 Bedienungsanleitung
(117 Seiten)
(117 Seiten)
Vernetzung APC AP9630 Bedienungsanleitung
(32 Seiten)
(32 Seiten)
Vernetzung APC AP9224110 Spezifikationen
(16 Seiten)
(16 Seiten)
Vernetzung APC AP9608 Spezifikationen
(9 Seiten)
(9 Seiten)
Vernetzung APC AP9608 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.142 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern