APC IP DSLAM Betriebsanweisung Seite 320
- Seite / 603
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
312
ifname <interface-
name>
Name of the span configuration profile.
Type: Modify -- Mandatory
Get -- Optional
wireintf TwoWire |
FourWire |
FourWireBitInterleave |
FourWireByteInterleaveE
nhanced |
FourWireBitInterleaveEn
hanced
This object configures the two-wire or optional
four-wire operation for SHDSL Lines.
FourWireBitInterleave are extensions over
standard RFC.
Type: Modify -- Optional
minlinerate
<minlinerate-val>
This object configures the minimum transmission
rate for the associated SHDSL Line in bits-per-
second (bps). If the 'minlinerate' equals the
'maxlinerate', the line rate is considered 'fixed'. If
the 'minlinerate' is less than the 'maxlinerate',
the line rate is considered 'rate-adaptive'.
Type: Modify -- Optional
maxlinerate
<maxlinerate-val>
This object configures the maximum
transmission rate for the associated SHDSL Line
in bits-per-second (bps). If the 'minlinerate'
equals the 'maxlinerate', the line rate is
considered 'fixed'. If the 'minlinerate' is less than
the 'maxlinerate', the line rate is considered
'rate-adaptive'.
Type: Modify -- Optional
psd Symmetric |
Asymmetric |
R1asymmetric |
R2asymmetric
This object configures use of
symmetric/asymmetric PSD (PowerSpectral
Density) Mask for the associated SHDSL Line.
Type: Modify -- Optional
txmode Region1 |
Region2
This object specifies the regional setting for the
SHDSL line.
Type: Modify -- Optional
rmtenabled Enabled |
Disabled
This object enables/disables support for remote
management of the units in an SHDSL line from
the STU-R via the EOC. Default value supported
is the deviation from standard RFC.
Type: Modify -- Optional
currcondtgtmgndown
<currcondtgtmgndown-
val>
This object specifies the downstream current
condition target SNR margin for an SHDSL line.
The Only range supported is 0 to 10. Default
value supported is also deviation from standard
RFC.
Type: Modify -- Optional
Valid values: 0 - 10
worstcasetgtmgndown
<worstcasetgtmgndown-
val>
This object specifies the downstream worst case
target SNR margin for an SHDSL line. The Only
range supported is -10 to 10. Default value
supported is also deviation from standard RFC.
Type: Modify -- Optional
Valid values: (-10) - 10
currcondtgtmgnup
<currcondtgtmgnup-val>
This object specifies the upstream current
condition target SNR margin for an SHDSL line.
The Only range supported is 0 to 10. Default
value supported is also deviation from standard
RFC.
Type: Modify -- Optional
Valid values: 0 - 10
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Verwandte Produkte und Handbücher für Vernetzung APC IP DSLAM
Vernetzung APC AP9312TH Betriebsanweisung
(32 Seiten)
(32 Seiten)
Vernetzung APC AP9608 Installationshandbuch
(32 Seiten)
(32 Seiten)
Vernetzung APC 66123 Installationshandbuch
(16 Seiten)
(16 Seiten)
Vernetzung APC AP9630 Betriebsanweisung
(85 Seiten)
(85 Seiten)
Vernetzung APC IP DSLAM Betriebsanweisung
(67 Seiten)
(67 Seiten)
Vernetzung APC AP9630 Bedienungsanleitung
(117 Seiten)
(117 Seiten)
Vernetzung APC AP9630 Bedienungsanleitung
(32 Seiten)
(32 Seiten)
Vernetzung APC AP9224110 Spezifikationen
(16 Seiten)
(16 Seiten)
Vernetzung APC AP9608 Spezifikationen
(9 Seiten)
(9 Seiten)
Vernetzung APC AP9608 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern